Narrator: AN 1880s INVENTION,
THE CAST-IRON TUB WAS FIRST MARKETED IN AMERICA
AS A HORSE TROUGH AND A HOG SCALDER,
WHICH COULD ALSO SERVE AS A BATHTUB.
IT WAS SOON MORE POPULAR IN THE BATHROOM THAN THE BARNYARD.
IT'S HEAT-RETAINING PROPERTIES
MADE A LONG AND LUXURIOUS SOAK POSSIBLE.
THE CAST-IRON TUB IS ONE INVENTION
THAT'S GOT A LOT OF PEOPLE IN HOT WATER,
AND THAT'S WHAT PEOPLE LIKE ABOUT IT.
TODAY, THEY MAKE CAST-IRON TUBS FROM SCRAP METAL --
THINGS LIKE OLD HEATING RADIATORS,
WATER PIPES, MANHOLE COVERS, AND EVEN SOME CAR PARTS.
RECYCLING SCRAP IRON
IS MORE ENERGY EFFICIENT AND CHEAPER THAN MINING IT.
A POWERFUL MAGNET AT THE END OF A CRANE ARM
LIFTS THE HEAVY IRON FROM THE SCRAP HEAP
AND TRANSFERS IT
TO BIG TRAYS KNOWN AS CHARGING PANS.
THE CHARGING PANS DELIVER THE SCRAP TO A CENTER TROUGH.
THIS TROUGH IS A SCALE.
IT WEIGHS THE SCRAP AND RELEASES IT TO A CONVEYER.
THE SCRAP HEADS INTO THE BATHTUB FACTORY.
INSIDE, IT FLOWS DIRECTLY
INTO AN ENORMOUS ELECTRIC INDUCTION FURNACE
HEATED TO MORE THAN 2,500° FAHRENHEIT.
THE SCRAP IRON MELTS INTO A POOL OF LIQUID METAL.
THEY RUN THIS FURNACE AROUND THE CLOCK,
AND IT'S ALWAYS TWO-THIRDS FULL
SO THAT NEWLY-ADDED SCRAP MELTS QUICKLY.
HUGE HYDRAULIC CYLINDERS TIP THE FURNACE FORWARD.
THE MOLTEN IRON FLOWS INTO A LADLE.
AN OVERHEAD TROLLEY
CARRIES THE LADLE BRIMMING WITH THE HOT LIQUID METAL
TO A HOLDING FURNACE WHICH MAINTAINS ITS TEMPERATURE
UNTIL THE NEXT STEP.
THEY'RE NOW READY
TO MAKE A TWO-PART CASTING MOLD FROM SAND
USING STEEL TUB PATTERNS.
TO MAKE ONE HALF OF THE MOLD, THEY FILL A TUB PATTERN
WITH A MIX OF MOIST SAND AND CLAY.
HYDRAULIC RAMS PACK IT DOWN,
AND THE MIX COMPACTS
AND TAKES THE SHAPE OF THE PATTERN.
THE CLAY IS THE BONDING AGENT
THAT CAUSES THE MIX TO HOLD THE SHAPE.
ONCE THE RAMS RETRACT,
THE MOLD TAKES A TRIP UNDER SOME BLADES
THAT SCRAPE OFF THE EXCESS SAND.
MACHINERY THEN LIFTS THIS HALF OF THE SAND MOLD
OUT OF THE STEEL PATTERN AND TRANSFERS IT
TO THE OTHER HALF OF THE MOLD PREPARED EARLIER.
THE TWO BATHTUB MOLDS NOW COME TOGETHER,
LEAVING A SMALL GAP BETWEEN THEM.
THE MOLTEN IRON, WHICH HAS BEEN TRANSFERRED
TO AN AUTOMATIC POURING SYSTEM,
FLOWS INTO PORTALS IN THE TOP OF THE MOLD
AND INTO THE GAP AT THE CENTER.
THE BATHTUB MOLDS THEN MOVE TO A COOLING LINE,
AND AFTER CHILLING HERE FOR ABOUT 20 MINUTES,
THE IRON INSIDE SOLIDIFIES.
THEN, IT'S INTO A SHAKER DEVICE THAT BREAKS APART THE SAND MOLD,
REVEALING THE NEWLY CAST IRON BATHTUB.
A ROBOT RETRIEVES THE BATHTUB AND STACKS IT.
NEXT, AN EMPLOYEE
SPRAYS SPECIALLY-FORMULATED GLASS POWDER
ONTO THE TUB.
IT'S AN UNDERCOAT FOR THE ENAMEL FINISH.
THEY BAKE THE TUB UNTIL IT'S RED-HOT.
IN THE HEAT,
THE GLASS POWDER MELTS AND ADHERES TO THE IRON TUB.
A HYDRAULIC DEVICE CALLED A MANIPULATOR
SETS THE TUB ON A PEDESTAL.
THE PEDESTAL SWIVELS
AS THEY APPLY TWO MORE GROUND-GLASS LAYERS.
THESE ARE THE ENAMEL TOPCOATS.
ON CONTACT, THE GLASS MIXTURE MELTS ONTO THE UNDERCOAT.
THE LAYERS OF GLASS FORM A PERMANENT BOND
WITH THE IRON CASTING.
BETWEEN COATS, THE TUB COOLS,
AND THEY SEND IT BACK INTO THE FURNACE FOR A REHEAT.
THEY PLACE A MASK IN THE BASE OF THE ENAMEL TUB.
THE MASK IS LIKE A STENCIL.
A ROBOT BLASTS FINE ALUMINA-OXIDE PARTICLES
INTO THE OPEN AREAS OF THE MASK.
THIS ETCHES AN ABRASIVE FINISH,
LEAVING A SUBTLE PATTERN ON THE SURFACE OF THE BATHTUB.
IT CREATES VISUAL INTEREST
AND ALSO PROVIDES A NON-SLIP SURFACE.
THE MASKS COME IN A VARIETY OF PATTERNS FOR DIFFERENT LOOKS.
WHETHER IT'S A MODERN DESIGN
OR THE TRADITIONAL CLAW-FOOT ONE,
THESE CAST-IRON TUBS SHOULD HAVE NO PROBLEM FINDING A HOME.
Narrator: THE HOPI, A NATIVE AMERICAN TRIBE
LIVING PRIMARILY IN NORTHEASTERN ARIZONA,
ARE KNOWN FOR CARVING KACHINAS,
WOODEN DOLLS REPRESENTING DEITIES,
ELEMENTS IN NATURE, OR THE SPIRITS OF ANCESTORS.
THEY ARE TRADITIONALLY PRESENTED IN A DANCE CEREMONY
TO THE GIRLS OF THE COMMUNITY.
HOPI KACHINA DOLLS ARE CHERISHED FAMILY KEEPSAKES
DESIGNED TO TEACH HOPI CHILDREN ABOUT THE DEITIES AND SPIRITS
CENTRAL TO THEIR ABORIGINAL TRADITIONS.
BESIDES CEREMONIAL PURPOSES,
MANY HOPI CARVERS PRODUCE KACHINA DOLLS
FOR SALE TO NATIVE ART ENTHUSIASTS.
THE CARVER USES KNIVES OF DIFFERENT SIZES,
SHARPENING THE STEEL BLADES AFTER EVERY 10 OR 15 MINUTES
TO PREVENT DULLING.
KACHINA DOLLS ARE TRADITIONALLY MADE OF COTTONWOOD --
NOT FROM THE TREE'S BRANCH, BUT FROM ITS ROOT.
THE CARVER BEGINS BY SHAVING OFF THE THIN OUTER BARK.
WITH A STRAIGHT CUT FROM ONE SIDE TO THE OTHER,
HE SHAPES A BIT OF THE SINGLE FEATHER
WHICH WILL ADORN THE TOP OF THIS DOLL'S HEAD.
HE MAKES A SERIES OF VERTICAL CUTS
TO FORM THE FACE AND HAIRLINE.
HE CONTINUES CARVING THE HEAD FORM,
THEN, WITH A WOOD-BURNING TOOL,
BURNS IN THE SQUARE OUTLINE OF THE FACE.
NOW HE SHAVES AWAY WOOD ABOVE AND BELOW
TO MAKE THE FACE PROTRUDE.
HE FORMS THE FACE IN MORE DETAIL...
...THEN PICKS UP THE WOOD-BURNING TOOL AGAIN,
THIS TIME TO DELINEATE THE NECKLINE...
...AND THE DOLL'S ROBE.
BACK TO CARVING.
NOW, WITH UPWARD STROKES,
HE SHAVES OFF WOOD TO SHAPE THE NECKLINE.
HE TAKES A LARGER KNIFE
AND REMOVES BIGGER PIECES OF WOOD
TO FINISH FORMING THE HEAD FEATHER.
NOW HE SANDS THE WOOD
WITH PROGRESSIVELY FINER SANDPAPERS
TO REMOVE ALL THE CUT MARKS LEFT BY HIS KNIVES
AND TO REFINE THE DOLL'S SHAPE.
WITH THE DOLL PERFECTLY FORMED NOW,
IT'S TIME FOR THE DETAILS AND DECORATIONS.
FIRST, HE SKETCHES IT ALL OUT IN PENCIL...
...THEN RUNS THE WOOD-BURNING TOOL ALONG THE LINES.
HE DECORATES THE BODY,
THEN MOVES ON TO THE DOLL'S HAIR AND FACIAL FEATURES.
IT'S THESE DETAILS THAT BRING THE DOLL ALIVE.
WHAT WAS A SIMPLE AND ORDINARY COTTONWOOD TREE ROOT
HAS GONE THROUGH CARVING, SANDING, AND BURNING
TO BECOME AN ALMOST-FINISHED KACHINA DOLL.
HE NOW COATS THE ENTIRE SURFACE WITH CLEAR VARNISH.
THIS SEALS THE WOOD
TO PREVENT IT FROM ABSORBING THE PAINT HE APPLIES NEXT.
ABOUT 40 MINUTES LATER,
THE VARNISH IS DRY AND THE PAINTING CAN BEGIN.
TRADITIONALLY, HOPI CARVERS MADE PAINT FROM NATURAL PIGMENTS
SUCH AS SAND, PLANTS, AND BERRIES.
TODAY'S CARVERS BUY READY-MADE OILS OR ACRYLICS.
THIS CARVER DILUTES ACRYLIC PAINT WITH WATER
TO MAKE IT TRANSPARENT.
THIS ALLOWS THE NATURAL BEAUTY OF THE WOOD GRAIN
TO SHOW THROUGH THE COLOR.
AFTER PAINTING, HE APPLIES A COAT OF CLEAR VARNISH
TO SEAL AND PROTECT THE SURFACE.
SOME CARVERS HAVE MOVED IN A NEW ARTISTIC DIRECTION -- BRONZE.
THEY USE THEIR WOODEN KACHINA DOLL TO PRODUCE A LATEX MOLD.
THEN, WITH THIS MOLD, CAST A WAX REPLICA.
THEY DIP THE REPLICA IN A SUBSTANCE
THAT HARDENS INTO A HEAT-RESISTANT SHELL.
THEN, THEY PUT THE SHELL IN A FURNACE TO MELT AWAY THE WAX.
THIS LEAVES A CAVITY IN THE SHAPE OF THE DOLL.
THEY POOR MOLTEN BRONZE INTO THE CAVITY,
AND WHEN THE BRONZE COOLS AND SOLIDIFIES,
THEY BREAK THE SHELL TO EXTRACT A BRONZE VERSION
OF THEIR KACHINA DOLL.
INSTEAD OF PAINTS,
THEY APPLY CHEMICALS THAT COLOR THE METAL --
A MODERN TWIST ON AN AGE-OLD HOPI ART.
Narrator: A MINE-TRUCK ENGINE IS A BEAST.
THE MOST POWERFUL ONES PACK A BRAWNY 24 CYLINDERS,
GENERATING 4,200 HORSEPOWER.
COMPARE THAT TO 200 HORSEPOWER
FOR A MID-SIZED CAR WITH SIX CYLINDERS.
BUT WHEN THEY START TO SHOW THE STRAIN,
IT'S TIME FOR A TOTAL REBUILD.
AFTER ABOUT 20,000 HOURS OF HAULING HEAVY ROCK,
IT'S TIME FOR RENEWAL.
MINE-TRUCK ENGINES ARE ROUTINELY REBUILT --
NOT JUST ONCE, BUT NUMEROUS TIMES.
IT'S CHEAPER THAN BUYING A NEW ENGINE,
AND IT SAVES PRECIOUS RESOURCES.
EACH REBUILD IS A MASSIVE UNDERTAKING --
VIRTUALLY EVERY COMPONENT OF THIS DIESEL ENGINE
WILL BE REMANUFACTURED OR REPLACED.
AS THE TEAM DISMANTLES IT,
THEY INSPECT EACH PART FOR WEAR AND TEAR.
THEY TAKE IT DOWN TO THE IMMENSE CRANKSHAFT,
THE HEART OF THIS MINE-TRUCK ENGINE.
WITH THE CRANKSHAFT REMOVED,
THEY PULL THE LENGTHY CAMSHAFT OUT OF THE CYLINDER BLOCK.
WITH THE ENGINE NOW IN PIECES,
THEY CLEAN EVERY PART THAT'S SALVAGEABLE,
INCLUDING THE HUGE CYLINDER BLOCK.
A COUPLE OF HOURS SOAKING IN A HOT SODIUM-PHOSPHATE SOLUTION
REMOVES THE GREASE AND EXPOSES THE BARE METAL.
ANY IMPERFECTIONS ARE NOW MORE APPARENT.
USING A DEPTH GAUGE,
A TECHNICIAN MAPS OUT FLAWS, LIKE THIS CRACK.
IT WILL NEED TO BE FILLED, AND HE MAKES A NOTE OF IT.
NEXT, A HIGH-SPEED MILLING TOOL
CARVES OFF A THIN LAYER OF THE STEEL,
TAKING THE CYLINDER BLOCK'S FINISH FROM GRIMY-GRAY
TO BRIGHT AND SHINY.
IT ALSO SMOOTHES AWAY ANY UNEVENNESS
TO CREATE A UNIFORM SURFACE
FOR SEALING GASKETS AROUND THE CYLINDERS LATER.
AFTER THE INTENSIVE MACHINING,
THE CYLINDER BLOCK LOOKS LIKE NEW.
IT'S BACK TO THE CRANKSHAFT NOW.
IT, TOO, HAS UNDERGONE AN EXTENSIVE CLEANING.
MACHINERY GRINDS THE OUTSIDE DIAMETER
TO A PRECISE TOLERANCE --
EQUIVALENT TO ONE-TWENTIETH OF A HUMAN HAIR.
THIS WILL ALLOW NEW, THICKER BEARINGS TO FIT TO IT.
THE TEAM CLAMPS WEIGHTS TO THE MACHINE CRANKSHAFT.
THESE WEIGHTS MIMIC THE LOAD OF ENGINE PARTS,
LIKE PISTONS AND RODS,
AS THEY NOW BALANCE THIS CRITICAL PART.
THE CRANKSHAFT ROTATES,
AND SENSORS DETECT VIBRATIONS AND PINPOINT THE PROBLEM.
AFTER MORE GRINDING IN THESE LOCATIONS,
THEY TEST IT AGAIN TO CONFIRM THE CRANKSHAFT IS BALANCED.
BACK TO THE CAMSHAFT NOW --
A MEMBER OF THE CREW USES A BLACK MARKER
TO HIGHLIGHT WEAR PATTERNS.
A GRINDER EVENS OUT THE WEAR,
AND IT ALSO MACHINES THE PROFILE OF EACH LOBE
AS IT FOLLOWS A METAL CAMSHAFT MASTER.
THE BLACK-MARKER LINES VANISH AS THE WEAR LINES ARE SMOOTHED,
AND THE PROFILE OF THE CAMSHAFT IS IMPROVED.
A MAJOR CLEAN-UP ALSO TRANSFORMS THE RODS
THAT CONNECT THE PISTON TO THE CRANKSHAFT.
A TECHNICIAN THEN PLACES THE ROD IN A SPECIAL HONING MACHINE
AND ACTIVATES IT.
FOUR ARMS WITH GRITTY ENDS GRIND THE INSIDE OF THE ROD-HEAD
AS THE TECHNICIAN MOVES THE ROD BACK AND FORTH.
THIS SIZES THE INNER DIAMETER TO ENABLE THE ROD
TO FIT TO THE OTHER REVAMPED PARTS.
ONCE ALL THE PARTS HAVE BEEN CLEANED AND MACHINED,
THE ENGINE IS READY FOR REASSEMBLY.
USING A CRANE, A TECHNICIAN LOWERS THE CRANKSHAFT
BACK INTO THE CYLINDER BLOCK.
HE SECURES THE CRANKSHAFT AT ONE END
WITH A METAL BRACKET CALLED A MAIN CAP.
THERE ARE ACTUALLY NINE MAIN CAPS IN TOTAL.
HE GIVES THE CRANKSHAFT A SPIN
TO CONFIRM THAT IT ROTATES FREELY
BEFORE INSTALLING THE REST.
WITH A PISTON NOW ATTACHED TO ONE END OF A CONNECTING ROD,
HE SLIDES THE OTHER END INTO A SLOT
IN THE CYLINDER BLOCK.
THIS PARTICULAR ENGINE IS A 16-CYLINDER ONE.
IT'S CONSIDERED MIDSIZE FOR MINING TRUCKS.
ONCE THE GASKETS HAVE BEEN FIXED TO THE CYLINDER BLOCK,
THEY BOLT THE CYLINDER HEADS TO IT.
THERE ARE HUNDREDS OF PARTS IN ONE OF THESE MONSTER ENGINES,
AND IT TAKES 700 PERSON HOURS FOR ONE REBUILD.
WITH THIS MINE-TRUCK ENGINE NOW FULLY ASSEMBLED,
THEY HOOK IT UP TO A DYNAMOMETER TO MEASURE ENGINE PERFORMANCE.
THEY RUN AT FULL TILT TO CONFIRM THAT IT'S FIRING ALL CYLINDERS
AND PERFORMING TO THE MAX.
THIS REBUILT MINE-TRUCK ENGINE
IS READY TO GO BACK INTO SERVICE.
STRONG AND HEAVILY BUILT, THIS NINE-TON DIESEL ENGINE
SHOULD PULL ITS OWN WEIGHT AND THEN SOME.
Narrator: MUSIC, PHOTOGRAPHS, DOCUMENTS --
WHAT USED TO TAKE UP SHELF SPACE IN OUR HOMES OFFICES
CAN NOW BE STORED ON A TINY MEMORY CARD
OR FLASH DRIVE.
YOU CAN SAVE YOUR FILES ON IT,
TAKE THEM OUT OF THE DEVICE AND TRANSPORT THEM ANYWHERE,
AS WELL AS DELETE DATA YOU NO LONGER NEED.
A MEMORY CARD FITS INTO A SLOT IN YOUR DIGITAL DEVICE.
A FLASH DRIVE PLUGS INTO A USB PORT.
THE KEY COMPONENT OF BOTH FORMATS --
A MEMORY CHIP,
PRODUCED IN A FACTORY
THAT'S 1,000 TIMES CLEANER THAN A HOSPITAL OPERATING ROOM.
IT ALL BEGINS WITH THE WAFER -- A THIN DISC OF PURE SILICON,
A NON-METALLIC NATURAL ELEMENT THAT CONDUCTS ELECTRICITY.
AN AUTOMATED CONTAINER SYSTEM
MOVES THE WAFER THROUGH MORE THAN 800 OPERATIONS.
AT EACH STOP,
THE WAFER RECEIVES ONE OF SEVERAL LAYERS
OF NON-CONDUCTIVE MATERIALS, SUCH AS SILICON DIOXIDE,
AND CONDUCTIVE MATERIALS, SUCH AS COPPER.
THE MACHINES COAT THE LAYER WITH LIGHT-SENSITIVE FLUID,
THEN APPLY UV LIGHT THROUGH A GLASS STENCIL
OF THE COMPLEX PATTERN OF ELECTRICAL CIRCUITRY.
THE EXPOSED AREAS OF FLUID CHEMICALLY REACT,
LOCKING THE MATERIAL DIRECTLY UNDERNEATH
INTO THE CIRCUITRY PATTERN.
CHEMICAL BATHS THEN REMOVE THE SURROUNDING FLUID AND MATERIAL,
LEAVING ONLY THE LAYER OF CIRCUITRY,
ELECTRICAL PATHWAYS 2,000 TIMES NARROWER
THAN A HUMAN HAIR.
A ROBOT TESTS THE CIRCUITRY FOR EVERY MEMORY CHIP ON THE WAFER.
A SINGLE WAFER, MEASURING 12 INCHES IN DIAMETER,
YIELDS HUNDREDS OF MEMORY CHIPS.
THE GOAL IS TO MAKE THOSE CHIPS AS SMALL AS POSSIBLE.
IN THIS INDUSTRY,
IT'S ALL ABOUT MAXIMUM MEMORY IN MINIMAL SPACE.
THAT'S WHY THIS OPERATION THINS THE CHIPS
BY GRINDING AWAY TWO-THIRDS OF THE SILICON
FROM THE BACKSIDE OF THE WAFER.
AND ONE LAST STEP BEFORE CUTTING THE WAFER
INTO INDIVIDUAL MEMORY CHIPS --
THIS MACHINE APPLIES TAPE
TO HOLD THE SEPARATED CHIPS TOGETHER.
A COMPUTER-GUIDED SAW SLICES THE CHIPS APART.
CUTTING SILICON IS LIKE CUTTING GLASS --
IT REQUIRES A DIAMOND-EDGE BLADE.
IN THE NEXT STEP, A ROBOTIC ARM,
FOLLOWING THE WAFER MAP GENERATED EARLIER,
PICKS UP THE CHIPS WHICH PASS TESTING
AND ATTACHES EACH ONE TO A FIBERGLASS LEAD FRAME.
THE TERM LEAD REFERS TO THE FRAME'S PINS,
WHICH CONNECT THE CHIP TO THE DIGITAL DEVICE.
ANOTHER ROBOT WIRES THE CHIP TO THE LEAD FRAME
WITH GOLD THREAD THAT'S ABOUT THE WIDTH OF A HUMAN HAIR.
GOLD IS VERY CONDUCTIVE, SO NOW THE PATHWAY IS COMPLETE.
ELECTRICITY WILL TRAVEL FROM THE CHIP'S CIRCUITRY,
THROUGH THE GOLD THREAD, TO THE PINS, TO THE DEVICE.
AFTER A MACHINE SEALS THE CHIP IN PLASTIC,
WORKERS GENTLY SNAP THEM APART
AND INSERT THEM IN MEMORY-CARD HOUSINGS.
THE PLASTIC AND METAL HOUSING IS FOR A MEMORY CARD FORMAT
KNOWN AS COMPACT FLASH.
A SMALL, AUTOMATED PRESS
LOCKS THE TWO HALVES OF THE HOUSING TOGETHER.
THE NEXT STATION LABELS THE FRONT OF THE HOUSING.
EVERY SINGLE MEMORY CARD UNDERGOES TESTING
FOR BOTH FUNCTION AND SPEED.
A LASER MACHINE ETCHES PRODUCT INFORMATION
INTO THE BACK OF THE HOUSING.
THESE ARE ANOTHER FORMAT CALLED SECURE DIGITAL, OR SD.
THEY'RE ASSEMBLED AND LABELED
JUST LIKE THE COMPACT FLASHCARDS.
WHEN THE FINISHED MEMORY CARDS COME OFF THE ASSEMBLY LINE,
WORKERS CONDUCT A FINAL, VISUAL INSPECTION.
ON THE FLASH DRIVE ASSEMBLY LINE,
MUCH THE SAME PROCESS.
A ROBOT PUTS 20 LEAD FRAMES ON 20 CIRCUIT BOARDS.
THEN, A WORKER POSITIONS 20 USB CONNECTORS,
WHICH A SOLDERING MACHINE BONDS TO THE CIRCUIT BOARDS.
THE FINAL STEP -- ELECTRONIC TESTING,
TO MAKE SURE THE USB CONNECTION IS WORKING,
AND VIA THE CIRCUIT BOARD, TALKING TO THE CHIP.
THE FLASH DRIVES ARE NOW READY TO GO INTO INDIVIDUAL HOUSINGS.
THIS MODEL HAS A TWO-PART PLASTIC HOUSING,
WHICH PIVOTS IN AND OUT OF A PLASTIC CASE,
THAT CAN CONVENIENTLY BE ATTACHED TO A KEY CHAIN
OR A LANYARD FOR EASY PORTABILITY.
FLASH DRIVE OR MEMORY CARD,
STORING YOUR DIGITAL EFFECTS IS JUST A CLICK AWAY.
-- Captions by VITAC -- www.vitac.com
CAPTIONS PAID FOR BY DISCOVERY COMMUNICATIONS
IF YOU HAVE ANY COMMENTS ABOUT THE SHOW,
OR IF YOU'D LIKE TO SUGGEST TOPICS FOR FUTURE SHOWS,
DROP US A LINE AT...